-
1.2G 3D printer control board
$97.09RepRap Rambo 1.2G 3D Printer Control Board Introduce: Rambo 1.2G is a microcontroller board of 3D printer which integrates the stepper motor, hotbed, extruder, fan driver and thermometry in one. Rambo 1.2G is completely compatible with Arduino in that it adapts the same IC, ATMEGA 2560, with Arduino mega2560. 3…
-
10 3D Printers 42 Stepper Motor Driver Expansion Board 8825 / A4988
$36.36Features: 1. On-board DIP switch, you can easily adjust the drive segments2. Terminal power connector for easy connection drive power3. Compatible with 12 / 24V drive scheme4. Suitable for 42 stepper motor drive, 3D printers and DIY Specifications: Size: 42 x 42 x 15mmFixed: 3mmPitch: 1400 x 1400mil (35.56 x…
-
10 Pcs RAMPS 1.4 end stop switch for RepRap Mendel 3D printers with 70 cm cable
$10.63Features: It using 22AWG wire, copper wire inside is very thick, can be resistant to current 2A, 300V voltage. An insulating layer over a wide range of temperatures, up to 80 degrees. Is the common connection of thin copper wire can not match. Not easy to pull off, plug it…
-
10Pcs 3D Printer A4988 Reprap Stepper Progressive Motor Driver Module
$18.06Description:A4988 is a complete microstepping motor driver with built-in translator for easy operation. This product is available in full, half, 1/4, 1/8 and 1/16 step modes operate bipolar stepper motors, output drive capacity of up to 35 V and 2 A. A4988 includes a fixed off-time current regulator, the regulator…
-
10Pcs 3D Printer Stepstick DRV8825 Stepper Driver Reprap 4-Layer PCB
$21.29Descriptions:The module has an interface pinout is almost the same with A4988 stepper motor drive carrier, so that it can be used as a higher performance in a pull-down menu the plates replaced in many applications.DRV8825 features an adjustable current limit, overcurrent and overtemperature protection, six micro-resolution (down 1/32-step).It uses…
-
10PCS CD 57/86 Stepper Motor Driver Current Expansion Board for 3D Printers
$27.24Perfect match with: (package does includes) Motor driver with 4.5A: MKS TB66003D printer motherboard: MKS-Gen Feature: In current 42 motor-driver of 3D printer on the market is that the direct primary IC connect to motor driver IC, the current consumed by each interface will not exceed 2MA.The MKS Gen motherboard…
-
10PCS for RAMPS 1.4 Reprap Mendel Prusa Arduinos 3D printer controller
$66.10Description: Fully assembled & tested, no soldering requiredIt is designed to fit the entire electronics needed for a RepRap in one small package for low costThe modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansionA…
-
10PCS TB6600 Upgrade 32 Section 4A 40V 57/86 Stepper Motor Driver
$104.50Features: 1. 9V-40V DC power supply2. H-bridge bipolar constant phase flow driver3. The maximum output current is 4.0A (eight optional)4. Up to 32 segments of six kinds of sub-modes available5. The input signal high-speed photoelectric isolatio6. Standard common anode single pulse interface7. Offline keep function8. Semi-enclosed chassis can adapt to…
-
10x CNC Shield + UNO R3 board + 4 x A4988 driver kit with heat sink for Arduino 3D printers
$125.47– CNC Shield BoardVersion: 3.0Color: RedSize(L*W*H): 68 x 53 x 18 mmVoltage: DC 12~36 V (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)Features:1. Uses removable A4988 or DRV8825 compatible stepper drivers.2. The extension board can be…
-
1284P Reprap Motherboard Board 3D Printer Controller
$40.57Specifications: -Processor: ATMEGA1284P (Sanguino compatible) -All screw connectors – no soldering -Mini USB interface -Material: PCB -Model: Melzi Reprap 2 -Working temperature: 100 -Media: Control panel -Scope of application: 3D printer Package included: 1x 3D printer circuit board
-
12V-24V MKS-GEN L motherboard with 4988 driver board for 3D printers
$51.14Specifications: Product Name: MKS-GEN L Main BoardSize: 90*60mmPower Input: 12V-24VWeight: about 95gFit For: 3D PrinterSuitable Model: A3s A5 Note: *Due to different producing batches, product details might be a little different. Thank you for understanding. Package Inlcuded: 1 x MKS-GEN L Main Board for 3D Printer
-
2-in-1 3D Printer Motherboard Control Panel with Mega2560 for RepRap Arduino Combination of R3 and Ramps 1.4
$39.67Overview: This board is the combination of Mega2560 R3 and ramps 1.4. In this case, you do not have any worries on the connection problems. It is compatible with A4988 and 8825 driver which is more flexible. In order to achieve better cooling, the board has the highest quality circuit…
